How To Install A New Pool Liner

How to install an Above Ground Pool Liner

Preparing your pool site....

To make certain your new liner fits well and looks great, y'all must set the pool earlier starting to fit the liner.

Brand sure yous have a good sand base. A suitable poisonous substance should be used liberally over the entire expanse to kill all the grass where your liner will be fitted.

The sand base should exist 50mm (2") deep over the entire floor of the pool, then it should form a cove all the mode around the wall of the pool surface area at to the lowest degree 150mm (6") high (see diagram A). This cove prevents the liner from being forced out underneath the wall of the pool and causing damage.

Step i
Smoothen and spread the sand using the dorsum of a garden rake or you lot can use a 1500mm (five') piece of timber every bit a screed. You may also find the sand easier to piece of work with if it's damp.

When the sand floor in the pool is completely smooth, compact it it by tamping or rolling. Finally you can employ a fine broom to remove any compaction marks and give a adept smooth terminate.

Step 2
Clean downwardly the walls of the pool to ensure that any sand and metal filings etc are removed, to prevent any harm to your liner. It is of import to then tape (PVC insulation tape is suitable) over the wall join bolts on the within wall of the puddle.

To obtain maximum life from your new liner, a basis sheet e.g. black plastic, should be placed over the sand before placing the liner in position. This tin be taped to secure information technology to the puddle wall above the sand cove for ease of fitting.

Remove the top copings from the puddle (if applicable to your puddle, virtually smaller pools have a small round metal capping that should non be removed). Also tape over whatsoever sharp edges of the metal capping earlier the liner is fitted.

Fitting your new Pool Liner.....

Step 1
Before unpacking your new liner, make sure it is the correct size as per the label as it cannot be returned once removed from the carton. Practice not use any type of knife or abrupt object to open up the carton.

With i or more people within the pool, pass the liner into the puddle and place it adjacent to one end (in the shallow or narrow end if applicative to your pool). Have care when handling the liner as sharp objects, even shoes, may damage it.

Step 2
Unroll the liner toward the other end of the pool and gently open it our making sure you exercise not disturb the level of the sand. The shiny side of the liner is the back which is placed against the sand, while the embossed side will hold the water.

Spread the liner so that the wall-to-flooring seam lies evenly (about midway) on the coving effectually the border of the pool. Identify the top edge of the liner over the wall of the puddle by about 150mm (vi") starting at each terminate get-go and then at either side (run across diagram B). Yous may need clothes pegs at this phase to agree the liner in place.

On some pools the liner may announced besides small in the perimeter. This can exist adjusted by evenly tensioning the perimeter of the liner as you place the acme edge over the wall of the puddle.

Check that at that place are no diagonal wrinkles in the wall of the liner as these indicate either an uneven overlap or the wall is non square with the bottom. This can exist easily adapted by moving the top of the liner in either a clockwise or anticlockwise direction until all wrinkles disappear. At present check that the seams on the floor of the liner are running straight and that the base of the liner is flat with all the large wrinkles removed.

Step 3
There are two methods of removing the remaining wrinkles in the liner - the hand method or the vacuum method. Choose a method and follow the instructions beneath. N.B. If the pool has a deep stop, you must apply the vacuum method.

Hand Method
Place a garden hose in the pool and be sure to remove any fittings that could damage the liner. The person plumbing fixtures the liner should get into the pool just prior to fitting, as the liner tin can exist slippery when information technology has a small layer of h2o on it.

Start filling the pool until you accept 25mm (1") of water over the entire floor. now turn the hose off.

Work out all the wrinkles in the floor past starting in the eye of the pool on your hands and knees (see diagram C). Gently push the wrinkles out in a round move, gradually moving all the surplus liner textile to the edges of the pool.

IMPORTANT:  If there is whatever more than 50mm (2") of water on the liner, it will be almost incommunicable to move any wrinkles and persistence may cause damage to your new liner.

Once y'all are happy that there are no wrinkles on the floor, adjust any surplus liner material over the edge of the pool and keep filling the puddle until the water is 150mm (half-dozen") deep (or until it is 50mm (2") to a higher place the cove). Remove the slack from the wall of the liner, section by section. The wall of the liner should not have any horizontal or diagonal wrinkles in it. Do Not OVER-TENSION THE LINER. Liners are designed to fit snug without any excess tension.

Secure the liner with the coping sections and continue to fill the pool to 300mm (12") deep. At this stage you need to check the tension of the liner around the perimeter of the pool and if necessary remove the sections of the coping near the afflicted area and release the tension. Now go along to the "Connecting the Filter" section.

Vacuum Method (must exist used for pools with deep ends)

Tape over the skimmer opening with a suitably sized piece of cardboard and masking tape. Place the hose of a vacuum cleaner (a Wet & Dry type is preferable) through the return pigsty in the wall of the pool until it is 300mm (12") above the sand. Tape around the hose at the wall to make information technology seal (see diagram D).

Double check that the liner has no large wrinkles or surplus material and make sure it is secured by the plastic strips. IF THE Puddle IS A DEEP Cease OR THE LINER APPEARS TO Be TIGHT, PLACE THE TOP Rail ON THE Puddle Earlier SWITCHING ON THE VACUUM CLEANER.

When the vacuum is turned on, you'll meet the liner start to suck down to the walls. Every bit information technology sucks downward, continually work the wrinkles out toward to edge of the puddle. You may have to switch the vacuum off to suit the tension of the liner a couple of times. This is quite normal.

In one case you have the liner vacuumed out and ALL the wrinkles removed, get-go filling the puddle with your garden hose. Brand sure any fittings on the hose are removed or protected and so they do non damage the liner. LEAVE THE VACUUM CLEANER RUNNING UNTIL THE Pool IS 300mm (12') DEEP. Now you tin turn the vacuum off. Carefully remove the vacuum hose from the wall of the pool, making certain you get all the record off and do not let any to fall in behind the liner. Remove the cardboard from the skimmer with the same care also.

Connecting the filter....

It is now time to connect your filtration organisation through your new liner, and again it is important that there is at least 300mm (12") of water over the floor of the pool. You tin can make full the pool to within 150mm (6") beneath the filtration openings.

Step 1
As per your manufacturers instructions, fit the skimmer box onto the wall of the pool past placing 1 gasket on the outside of the wall and the other between the liner and the escutcheon plate (plastic face plate). It is advisable to use a clear silicone sealant on all faces for a positive sealing.

Step 2
Secure the escutcheon plate in place with the screws provided with the skimmer box and when fully secured, neatly and carefully trim the liner material from the skimmer opening with a sharp knife.

Pace 3
To fit the pool return, cut a hole in the liner 10mm (3/8") smaller than the hole in the wall of the puddle. Fit the return plumbing equipment through the wall using a gasket or silicone sealant on each side of the wall. Tighten the fitting firmly to ensure there are no leaks.

Footstep iv
Connect the rest of the filtration (if required) then fill your puddle to the desired operating level, commonly half style upwards the skimmer opening. At present, chemically balance your water before using the pool. The staff at Direct Pool supplies can advise you on this.

HAPPY SWIMMING!

Source: https://www.directpoolsupplies.com.au/pool-liner-installation/

Posted by: lindseywisideeple.blogspot.com

Share this post